How to get factory backup camera out subaru?

Are you looking to remove the factory backup camera from your Subaru?

Whether you’re upgrading to a new system or replacing a damaged unit, removing the factory-installed backup camera is a manageable task if approached carefully.

Subarus, like many other vehicles, come with backup cameras integrated into the rear of the car, usually near the license plate.

To ensure a smooth removal process, you’ll need to carefully detach the camera from its housing, disconnect the wiring, and possibly remove any panels or trim.

In this guide, we’ll walk you through the essential steps to safely remove the camera without causing any damage.

Here, How to get external camera monitore to display evreyething?

How do I turn off the backup camera on my Subaru Outback?

To turn off the backup camera on your Subaru Outback, you typically need to follow a few simple steps, depending on your model and year.

In most cases, the backup camera is activated automatically when you shift into reverse. However, if you want to manually disable it or stop it from appearing on the screen, you can follow these general instructions:

1. Use the Settings Menu: On newer Subaru models, you can access the settings from the infotainment screen. Navigate to the “Camera” or “Display” settings and look for an option to turn off the backup camera or adjust its visibility.
2. Switch to a Different Screen: Some models may allow you to switch to another screen, such as the navigation or radio display, when the car is in reverse, thereby hiding the camera view.
3. Disable via Vehicle Settings: In certain cases, the camera might be linked to the vehicle’s overall settings, which can be adjusted through the Subaru Starlink system.

Consult your owner’s manual for specific instructions tailored to your Subaru Outback model.

How do I reset my reverse camera?

Resetting your reverse camera is usually a straightforward process and can help resolve issues such as a blank screen or distorted image. Here’s how you can reset it:

Here, How to get external camera monitore to display?

1. Turn Off the Vehicle: Start by turning off your car and leaving it off for about 10-15 minutes. This can help reset the system’s electronics, which might resolve temporary glitches.
2. Disconnect the Vehicle Battery: If the simple restart doesn’t work, you can disconnect the negative terminal of the vehicle’s battery for about 10-15 minutes. This cuts power to the camera system and forces a reset. Make sure to reconnect the terminal securely afterward.
3. Check Camera Connections: Inspect the camera and wiring for any loose or damaged connections. A poor connection could be the cause of the issue. Tightening or fixing these connections might reset the camera.
4. Consult Your Manual: If these steps don’t work, refer to your vehicle’s manual or visit a professional for further assistance.

These steps should help restore your backup camera functionality.

Why is my Subaru backup camera not working?

How do I clear my reverse camera?

To clear your reverse camera display, follow these steps depending on your issue:

Here, how to fix msi laptop camera?

1. Clean the Camera Lens: Dirt, mud, or snow can obstruct the camera’s view. Use a soft, microfiber cloth to gently clean the lens. This can help clear up any blurry or distorted images.
2. Reset the Camera Settings: If the camera display shows incorrect settings or errors, try resetting the system. In your Subaru, go to the infotainment menu and navigate to the camera or display settings. Look for an option to reset or restore default settings.
3. Disconnect the Battery: If the camera display remains stuck or unresponsive, disconnect the vehicle’s battery for 10-15 minutes. This will reset the camera system and might resolve any glitches.
4. Check for Obstructions: Ensure that no objects are blocking the camera’s view. Obstructions can cause a fuzzy or unclear display.

If these steps don’t clear the issue, consider consulting a professional.

How to get factory backup camera out subaru?

To remove the factory backup camera from your Subaru, follow these steps:

1. Prepare the Tools: You’ll need a trim removal tool, a screwdriver, and possibly a socket wrench to remove screws or bolts.
2. Disconnect the Battery: For safety, disconnect the negative terminal of the battery to avoid electrical shock or triggering airbags.
3. Remove the Trim and Panels: Start by carefully removing the trim or panel around the backup camera. Use the trim removal tool to avoid damaging the interior.
4. Unscrew the Camera Housing: The camera is usually mounted near the license plate or integrated into the rear bumper. Remove any screws or bolts holding the camera housing in place.
5. Disconnect the Wiring: Carefully disconnect the wiring harness attached to the camera. This will allow you to remove the camera entirely.
6. Remove the Camera: Once disconnected, you can pull the camera out of its housing.

If you encounter any difficulty, refer to your Subaru’s manual or consult a professional.

7 Steps to get factory backup camera out subaru

1. Disconnect the Vehicle Battery

Before starting any removal process, it’s essential to disconnect the vehicle’s battery. This ensures safety by preventing any electrical shocks or triggering of the airbags while you work with the backup camera. To do this, locate the negative terminal of the car’s battery, typically marked with a minus (-) sign.

Use a wrench to loosen the bolt and remove the cable from the terminal. Leave it disconnected for at least 10 minutes to ensure all systems are powered down. Disconnecting the battery also helps reset electronic systems, minimizing the chance of electrical issues when you reassemble the components.

Here, How to find model number on sony camera?

2. Remove the Trim and Panel Around the Camera

To access the backup camera, you’ll need to remove the trim or panels that cover the area. Subaru vehicles typically have a panel near the license plate or integrated into the rear bumper where the camera is located.

Use a plastic trim removal tool to carefully detach the panel without damaging the surrounding surfaces. Gently pry around the edges, working your way around the panel.

Take your time to avoid cracking or scratching the trim. In some models, you may need to remove screws or fasteners to fully remove the panel.

3. Unscrew the Camera Housing

Once you have access to the camera, you’ll need to unscrew the camera housing from its position.

Subaru typically uses screws or bolts to secure the housing. Using a screwdriver or socket wrench, remove the screws or bolts holding the housing in place.

Keep track of these fasteners as you will need them when reinstalling the new camera or trim. It’s a good idea to take note of the housing orientation to help when reinstalling the new camera. Some models may also use clips, which you can gently pry off with a trim tool.

4. Disconnect the Wiring Harness

The next step involves disconnecting the wiring harness connected to the backup camera. Look for the electrical connector that attaches the camera to the vehicle’s electrical system.

This can usually be done by pressing the clip and gently pulling the connector apart. Be cautious not to yank on the wiring, as this can damage the cables or connectors.

If the wiring is difficult to remove, check for any locking mechanisms that may require you to unlock or release the connector before pulling it apart. Keep the connector and cables safe for future use or reinstallation.

5. Remove the Camera from Its Housing

After disconnecting the wiring, you can now remove the camera from its housing. Most Subaru backup cameras are secured within a plastic housing or bracket. Depending on the design, you may need to gently pull the camera out, ensuring you don’t damage any surrounding parts.

Take care not to break any clips or brackets that hold the camera in place. If the camera is stuck, check for additional screws or clips that may be holding it in position. Once the camera is free, carefully remove it and set it aside for replacement or inspection.

6. Inspect the Camera and Wiring

Before installing a new backup camera or reassembling the components, it’s a good idea to inspect the old camera and wiring for any damage. Check the camera lens for cracks or dirt, and inspect the wiring for any signs of wear or corrosion. If the camera appears faulty or damaged, it may need to be replaced.

Here, How to discover a new camera?

Similarly, damaged wires or connectors may cause the backup camera to malfunction, so it’s important to repair or replace them before reinstallation. Make sure everything is in working order to ensure that the new or reinstalled camera functions properly.

7. Reassemble and Test the Camera

After replacing the camera or making any necessary repairs, it’s time to reassemble the components. First, connect the wiring harness back to the camera, ensuring it’s securely attached. Next, place the camera back into its housing or bracket, ensuring it is properly aligned and secured.

Once the camera is in place, screw the housing back into the vehicle, ensuring all screws or clips are tightened. Reinstall the trim or panel around the camera, making sure it fits snugly and is properly aligned.

Finally, reconnect the vehicle’s battery and test the camera by shifting the car into reverse. Ensure the camera displays a clear image on the screen and that it functions as expected. If everything looks good, your installation is complete!

Hook factory backup camera to aftermarket radio screen

To hook a factory backup camera to an aftermarket radio screen, follow these steps:

1. Locate the Camera’s Wiring: Identify the camera’s wiring harness, typically near the rear bumper or license plate area. This includes the video signal cable and the power wires.
2. Identify the Video Input on the Aftermarket Radio: Check the back of your aftermarket radio for a video input port (usually labeled “CAM IN” or “VIDEO IN”). Most aftermarket radios with backup camera compatibility will have this port.
3. Connect the Video Signal Cable: Use an RCA adapter to connect the camera’s video output cable to the video input port on the aftermarket radio. Ensure the connection is secure.
4. Power the Camera: Connect the camera’s power wire to the reverse light’s power source. This triggers the camera to turn on when the car is in reverse.
5. Test the Connection: Once everything is connected, test the backup camera by shifting your vehicle into reverse. The image should appear on the aftermarket radio screen.

Make sure to check the radio’s manual for any additional specific wiring instructions.

Back up OEM camera installation

Installing an OEM (Original Equipment Manufacturer) backup camera typically involves several steps to ensure proper functionality and integration with your vehicle’s system. Here’s a general guide:

1. Prepare the Tools and Equipment: You’ll need a new OEM backup camera, wiring harness, screws, trim removal tools, and a screwdriver. Make sure you have the necessary connectors and adapters for your vehicle.
2. Remove Interior Trim: Begin by removing the interior trim around the area where the camera will be mounted, typically near the license plate or rear bumper. Use trim removal tools to avoid damaging the panels.
3. Mount the Camera: Install the camera in its designated spot, securing it with screws or clips as required. Ensure it’s properly aligned for optimal rearview visibility.
4. Connect the Wiring: Connect the camera’s video signal and power cables. The power is usually connected to the reverse light, while the video signal goes to the display unit.
5. Test the Camera: Reassemble the trim and test the camera by shifting into reverse. Ensure the image displays correctly on the screen. If necessary, adjust the camera’s angle for better visibility.

2015 – Using OEM backup cam and aftermarket radio?

Using an OEM backup camera with an aftermarket radio in a 2015 vehicle involves a few key steps to ensure compatibility and proper functionality. Here’s how to integrate the two:

Here, How to check the battery on your ring camera?

1. Identify Connections: The OEM backup camera typically connects to the factory radio using a specific wiring harness. Since you’re using an aftermarket radio, you may need an RCA adapter to connect the camera’s video signal to the aftermarket radio’s video input port.
2. Power the Camera: The camera needs a power source, typically wired to the reverse light circuit. This ensures the camera activates when the vehicle is in reverse. You may need to splice into the reverse light wiring or use an adapter specific to your aftermarket radio.
3. Connect the Video Signal: Use an RCA cable to connect the camera’s video output to the “CAM IN” or “VIDEO IN” port on the aftermarket radio.
4. Test the System: After wiring everything, test the camera by shifting into reverse. Adjust the camera’s angle if necessary to ensure optimal rear visibility.

This setup should enable you to use the OEM camera with your new aftermarket radio seamlessly.

2011 – Would like to install a backup camera – is it prewired for OEM backup camera?

For a 2011 vehicle, whether or not it is prewired for an OEM backup camera depends on the make and model.

Some vehicles, especially higher trim levels or those with advanced safety features, may come prewired with a backup camera and the necessary connections for easy installation. However, most base models or older vehicles may not be prewired for a backup camera.

To check if your 2011 vehicle is prewired, start by inspecting the rearview mirror or infotainment system for a camera input port.

If your vehicle has a display screen that supports a backup camera, there’s a higher chance it’s prewired. Additionally, check the trunk or rear bumper area for wiring harnesses, or consult the owner’s manual to confirm if the wiring is in place.

If your vehicle isn’t prewired, you can still install a backup camera by running the necessary wiring from the rear to the radio or display unit. Professional installation may be recommended for a seamless setup.

2014 – Outback – Aftermarket backup camera for oem navi?

Installing an aftermarket backup camera for the OEM navigation system in a 2014 Subaru Outback is possible, but it requires some additional components for proper integration.

Here,  How to change fps sony camera?

The OEM navigation system in the Outback may not have the same video input as aftermarket radios, so you’ll need an adapter to make the connection.

Here’s how you can proceed:

1. Choose the Right Camera: Select an aftermarket backup camera that’s compatible with your Outback. Ensure it fits the mounting location, typically near the license plate or bumper area.
2. Wiring Harness/Adapter: You’ll need an RCA to factory harness adapter that allows the aftermarket camera’s video signal to connect to the OEM navigation screen. This adapter ensures the video output from the camera is compatible with the navigation system.
3. Power Connection: The camera will need to be wired to a power source, usually the reverse light, so it activates when the car is in reverse.
4. Professional Installation: Depending on your technical skills, professional installation might be the best option to ensure the wiring and connections are properly done.

After installation, test the camera by shifting into reverse, and the image should appear on the navigation screen.

Related faq’s

How to get factory backup camera out subaru outback

How to get factory backup camera out subaru forester

To remove the factory backup camera from a Subaru Forester, follow these steps:

1. Disconnect the Battery: For safety, disconnect the negative terminal of the battery.
2. Remove Interior Trim: Use a plastic trim tool to carefully remove the panel surrounding the camera, typically near the license plate or bumper.
3. Unscrew the Camera: Remove the screws or bolts securing the camera housing in place.
4. Disconnect the Wiring: Unplug the camera’s wiring harness.
5. Remove the Camera: Gently pull the camera out of its housing.

Refer to your Forester’s manual for more specific details if needed.

How to get factory backup camera out subaru impreza

To remove the factory backup camera from a Subaru Impreza, follow these steps:

1. Disconnect the Battery: Start by disconnecting the negative terminal of the battery for safety.
2. Remove the Trim Panel: Use a trim removal tool to gently detach the panel surrounding the camera, usually near the license plate or rear bumper.
3. Unscrew the Camera: Locate and remove any screws or bolts securing the camera housing.
4. Disconnect the Wiring: Unplug the wiring harness from the camera.
5. Remove the Camera: Carefully pull the camera out of its housing.

Check the vehicle’s manual for model-specific instructions if necessary.

How to get factory backup camera out subaru reddit

To remove a factory backup camera from a Subaru, Reddit users recommend the following:

1. Disconnect the Battery: Always disconnect the negative terminal to avoid electrical issues.
2. Remove the Trim: Use plastic trim tools to carefully remove the panel or trim around the camera, typically near the license plate.
3. Unscrew the Camera: Find and remove the screws or bolts securing the camera in place.
4. Disconnect the Wiring: Unplug the camera’s wiring harness.
5. Remove the Camera: Gently pull the camera out of its housing.

Reddit users suggest checking the vehicle’s manual or specific Subaru forums for additional tips and guidance.

2014 Subaru Outback backup camera replacement

Replacing the backup camera in a 2014 Subaru Outback involves a few key steps:

1. Disconnect the Battery: Start by disconnecting the negative terminal of the battery to ensure safety.
2. Remove the Trim: Use a trim removal tool to carefully take off the panel surrounding the camera, typically near the rear bumper or license plate.
3. Unscrew the Old Camera: Locate and remove the screws or bolts securing the camera.
4. Disconnect the Wiring: Unplug the camera’s wiring harness.
5. Install the New Camera: Connect the new camera, secure it with screws, and reassemble the trim.

Test the new camera to ensure proper functionality.

2011 Subaru Outback backup camera not working

If the backup camera in your 2011 Subaru Outback isn’t working, several factors could be causing the issue. First, check the camera lens for dirt or obstructions that may impair visibility.

Next, ensure the camera’s wiring is securely connected, especially the power and video signal cables. If the wiring appears intact, inspect the reverse light circuit, as the camera typically powers on when the vehicle is in reverse. A blown fuse or malfunctioning camera module could also be the problem.

If basic troubleshooting doesn’t resolve the issue, consider seeking professional help to diagnose and repair the system.

2012 Subaru Outback backup camera replacement

Replacing the backup camera in a 2012 Subaru Outback involves several steps:

1. Disconnect the Battery: Begin by disconnecting the negative terminal of the battery to avoid electrical issues.
2. Remove the Trim: Use a trim removal tool to carefully remove the panel around the camera, usually located near the rear bumper or license plate.
3. Unbolt the Old Camera: Locate and remove the screws or bolts securing the old camera.
4. Disconnect the Wiring: Unplug the wiring harness from the camera.
5. Install the New Camera: Connect the new camera, secure it, and reassemble the trim.

After installation, test the camera to ensure it’s functioning properly.

Replace Subaru backup camera

Replacing a Subaru backup camera involves a few straightforward steps:

1. Disconnect the Battery: For safety, disconnect the negative terminal of the battery to prevent electrical issues.
2. Remove the Trim: Use a trim removal tool to carefully detach the panel or trim around the camera, typically located near the rear bumper or license plate.
3. Unscrew the Camera: Locate the screws or bolts securing the camera and remove them.
4. Disconnect the Wiring: Unplug the camera’s wiring harness.
5. Install the New Camera: Connect the new camera, secure it with screws, and reassemble the trim.

Test the camera to ensure it works properly after installation.

Gen 4 OEM Backup Camera Replacement

Replacing the Gen 4 OEM backup camera involves several steps:

1. Disconnect the Battery: Start by disconnecting the negative terminal to ensure safety during the process.
2. Remove the Trim Panel: Use a plastic trim removal tool to carefully remove the panel surrounding the camera, often located near the rear bumper or license plate.
3. Unscrew the Camera: Remove the screws or bolts securing the OEM camera in place.
4. Disconnect the Wiring: Unplug the camera’s wiring harness, taking note of how it’s connected.
5. Install the New Camera: Connect the new camera, secure it with screws, and reassemble the trim.

Test the camera after installation to confirm proper functionality.

Retaining OEM backup camera with after market HU (2017 w/o nav, and w/o HK)

To retain the OEM backup camera when installing an aftermarket head unit (HU) in a 2017 Subaru Outback without navigation and Harman Kardon (HK) system, you’ll need an appropriate adapter.

Start by using an RCA-to-factory camera harness adapter that allows the OEM camera’s video signal to connect to the aftermarket HU’s camera input.

You’ll also need to connect the camera’s power wire to the reverse light circuit so it activates when the vehicle is in reverse. Finally, ensure proper alignment and test the system to confirm the camera functions as intended with the new head unit.

Replacing factory head unit — possible to re-route backup cam from rear view mirror?

When replacing a factory head unit, it’s possible to re-route the backup camera signal from the rearview mirror to the new unit, but it requires some work. Most vehicles with backup cameras display the feed on the factory screen or rearview mirror.

To reroute the camera, you’ll need a camera extension cable or a compatible RCA harness that connects the camera to the new head unit.

Additionally, you may need to adjust the wiring, ensuring the camera receives power from the reverse light circuit. Professional installation is often recommended to ensure proper functionality and avoid electrical issues.

Factory NAV MOD: Backup Camera install and VGA input (2008 Outback)

Installing a backup camera and adding a VGA input to the factory navigation system in a 2008 Subaru Outback requires a few key steps.

First, purchase a compatible backup camera and VGA input adapter. For the camera, mount it near the license plate and connect it to the reverse light circuit for power. Use an RCA cable to connect the camera to the factory NAV system via the VGA input adapter.

Ensure the adapter is wired correctly to allow the video signal to display on the navigation screen when the car is in reverse. Professional installation may be required for optimal results.

Factory NAV MOD: Backup Camera install and VGA input (2008 Outback)

To install a backup camera and add a VGA input to the factory navigation system in a 2008 Subaru Outback, follow these steps:

1. Purchase Components: Get a compatible backup camera and a VGA input adapter for the factory navigation system.
2. Camera Installation: Mount the camera near the rear license plate and connect it to the reverse light circuit for power.
3. Wiring the Camera: Use an RCA cable to connect the backup camera to the VGA input adapter.
4. Connect VGA Adapter: Integrate the VGA adapter into the factory navigation system to display the camera feed on the screen.
5. Test: Ensure the camera activates when the vehicle is in reverse, displaying the video feed correctly.

For a seamless installation, professional help may be needed to ensure compatibility and proper wiring.

Running backup camera wire

Running a backup camera wire involves a few essential steps:

1. Plan the Route: Start by identifying the best path for the wiring from the camera to the head unit. Typically, the wire will run from the rear bumper to the front of the vehicle.
2. Access the Interior: Remove trim panels, interior covers, or the headliner to route the wire through the cabin.
3. Drill a Hole (if necessary): If there’s no existing hole, carefully drill one in the rear of the vehicle to feed the camera’s cable.
4. Connect to Power: Tap into the reverse light circuit to provide power to the camera.
5. Test: Once the wire is connected, test the camera to ensure it activates when in reverse.

Ensure the wire is securely routed to avoid damage from vibrations or weather.

Tapping into OEM back up camera

Tapping into an OEM backup camera involves accessing the vehicle’s existing camera wiring to integrate with an aftermarket system or modify its functionality. First, locate the camera’s wiring harness, usually near the rear bumper or tailgate.

You’ll need to identify the power, ground, and video signal wires. The power wire is typically connected to the reverse light circuit, which powers the camera when the car is in reverse.

Use a wire tap or splice to connect the camera’s video signal to the new display or aftermarket system. Ensure all connections are secure and test the system to confirm proper operation.

Aftermarket HU with Backup Camera?

Installing an aftermarket head unit (HU) with a backup camera involves a few key steps.

First, ensure the new HU has a dedicated input for a backup camera. Mount the camera near the rear license plate and run the camera’s power wire to the reverse light circuit, so it activates when the vehicle is in reverse.

Connect the video signal wire from the camera to the HU’s camera input, typically using an RCA cable.

Some HUs may require an adapter or additional wiring for proper integration with the vehicle’s electrical system. Finally, test the camera to ensure proper functionality when reversing.

Add Backup Camera?

Adding a backup camera to a vehicle involves several steps. First, purchase a compatible camera system designed for your vehicle.

Mount the camera near the rear license plate, ensuring it has a clear view of the area behind the vehicle. Next, route the camera’s power wire to the reverse light circuit so it activates when the car is in reverse.

Connect the camera’s video output to the head unit or display screen, typically using an RCA cable. Secure the wiring, reassemble any removed panels, and test the system to ensure the camera functions correctly when the vehicle is in reverse.

Factory backup camera to aftermarket head unit?

To connect a factory backup camera to an aftermarket head unit, you’ll need an appropriate adapter or wiring harness.

First, locate the camera’s video signal and power wires, typically near the rear bumper. Disconnect the factory head unit and remove the trim panels to access the camera wiring.

Use an RCA-to-factory camera adapter to connect the camera’s video output to the new head unit’s camera input.

Ensure the camera’s power wire is connected to the reverse light circuit to activate when the vehicle is in reverse. Once everything is connected, test the camera to ensure proper functionality with the aftermarket system.

Backup camera relocation! (Rear tire mount)

Relocating a backup camera to a rear tire mount involves a few key steps. First, remove the camera from its original mounting location and carefully disconnect the wiring.

Choose a suitable spot on the rear tire mount that offers an unobstructed view of the area behind the vehicle. Mount the camera securely, ensuring it’s angled correctly for optimal visibility.

Next, run the camera’s wiring along the vehicle’s rear, securing it to prevent damage. Connect the power wire to the reverse light circuit, and the video signal wire to the display or head unit. Test the system to confirm proper functionality.

Conclusion 

In conclusion, removing a factory backup camera from a Subaru involves several key steps, including disconnecting the vehicle’s battery for safety, removing the trim or panels surrounding the camera, unscrewing the camera from its mount, and disconnecting the wiring harness.

Take care to avoid damaging any components during the removal process, and consider keeping track of screws or clips to ensure reassembly is smooth.

If you’re unsure or lack the proper tools, it may be helpful to consult a professional or refer to the vehicle’s manual. Once removed, you can replace or re-route the camera as needed.